Hw-module slot command

To convert the High-Speed Serial Interface (HSSI) into a clock master, use the hssi internal-clock command in interface configuration mode.Support in a specific 12.2SX release of this train depends on your.Note The International Telecommunication Union Telecommunication Standardization Sector (ITU-T) carries out the functions of the former Consultative Committee for International Telegraph and Telephone (CCITT).Configure national bit 1 only when required for interoperability with your telephone company.Resource: Getting Started with the AIP-SSM. hw-module module slot. The administrator can use the hw-module module 1 recover command to load a recovery.To select the frame type for the T1 or E1 data line, use the framing command in controller configuration mode.The hw-module command cannot be used to reset route processor controllers and switch controllers.This command is not supported on Catalyst 6500 or Cisco 7600 series.The output of the show logging onboard slot r0 status command is given both before and after onboard logging is disabled to verify that onboard logging was properly disabled.

Use this command if the equipment on the other end is capable of full-duplex mode.To configure a port to send or receive pause frames, use the flowcontrol command in interface configuration mode.If you want the hardware to stay in the stop state across system reloads, use the hw-module slot slot shutdown global configuration command.When the interface has something to transmit, it asserts DCD, waits a user-configured amount of time, then starts the transmission.Obtains predictable results regardless of whether a remote port is set to on, off, or desired.Specifies a primary (and backup) DHCP server to allocate IP addresses to MS users entering a particular PDN access point.Displays the current configuration and the operating status of the PXF stall monitor.a simple nginx module Raw. ngx_http_hello_world, // The command handler:. hlcf = ngx_http_get_module_loc_conf (r, ngx_http_hello_world_module).To enable a supervisor engine switchover when excessive fabric.

To start, stop, reload, or enable logging for an Embedded Services Processor (ESP), Route Processor (RP), or Shared Port Adapter (SPA) Interface Processor (SIP) on a Cisco ASR 1000 Series Aggregation Services Router, use the hw-module slot command in privileged EXEC or global configuration or diagnostic mode.This command was modified to include information on FDDI full-duplex, single-mode, and multimode port adapters.This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

You need extensive knowledge of the PCM state machine to tune this timer.To reset a specific port adapter, use the hw-module EXEC command.The following example changes the TL-Min time from 30 microseconds to 100 microseconds on a Cisco 7500 series router.

This command applies only to low-speed serial DCE interfaces in half-duplex mode.Indicates either a half-width card or daughter card attached to full-width cards.Specifies the chassis slot number where the module installed.

The QA error interrupt causes the RSP to dump the QA diagnostics and perform a cbus complex during which all the line cards are reloaded.To place a low-speed serial interface in controlled-carrier mode, instead of constant-carrier mode, use the half-duplex controlled-carrier command in interface configuration mode.The following examples place the interface in controlled-carrier mode and then back into constant-carrier operation.Hearts of Iron IV (HoI4) Cheats: Get. Print out all console commands or a specific command description. - reload loc (reloads localisation files).Refer to the Cisco Product Catalog for specific model numbers of port adapters.The following example shows a Cisco 7513 router with the active RSP loaded in slot 6 and the standby RSP loaded in slot 7.

Increasing the value does not necessarily mean more frames will be transmitted on each token capture.To disable and return to a maximum limit of 8100 VLANs per SPA, use the no form of this command.This command is supported on the WS-X6708-10G-3C and the WS-X6708-10G-3CXL modules only.

This command is supported on Cisco 7600 series routers that are configured with a Supervisor Engine 2 only.This command was introduced into the Cisco NCS 4200 Series and Cisco ASR 900 Series Routers.The following example shows how to deactivate the line card, MSC, or PCI port adapter carrier card in slot 2.This command is useful when you want to restart all interfaces on a SPA.This MOTD banner is useful for displaying messages that affect all users (such as impending system shutdowns).

When in this mode, if you manually plug in a second SPA, or if you attempt to reset the SPA (by entering a.

Cisco Application Control Engine (ACE) Troubleshooting

For example, the following message is displayed if the interface does not support full-duplex.Specifies the facility alarm for the environmental monitor temperature.

To configure Frame Relay payload compression for each Frame Relay port, use the frame-relay command in interface configuration mode.The reload keyword was added to enable a remote reload of a feature board.how to handle twice requests in nginx module. ngx_conf_t *cf); static ngx_command_t ngx_http. ngx_conf_set_flag_slot, NGX_HTTP_LOC_CONF.Significant processor memory is allocated to maintain the history information.Gigabit Ethernet ports default to off for receive and desired for send.Cisco recommends that the queue length not exceed10 packets on.The Excalibur and Ethernet Services cards do not have the reload option.

On the PRE2, use the facility-alarm core-temperature command.

LC3 System Start-Up Assumptions What would a real LC3 do

If there are more than the fddi frames-per-token value in the transmit ring, the specified value is transmitted before the token is passed on.Set if topology rules include the connection of a physical-to-physical type at the end of the connection.Use this option if the standby RP is experiencing problems and does not respond to the reload option.